Register

Recent questions tagged applied-mechanics-and-design

0 answers
0 votes
GATE2016-1-33
The figure shows cross-section of a beam subjected to bending. The area moment of inertia (in $mm^4$) of this cross-section about its base is ________
The figure shows cross-section of a beam subjected to bending. The area moment of inertia (in $mm^4$) of this cross-section about its base is ________
0 answers
0 votes
GATE2016-1-12
The spring constant of a helical compression spring DOES NOT depend on coil diameter material strength number of active turns wire diameter
The spring constant of a helical compression spring DOES NOT depend oncoil diametermaterial strengthnumber of active turnswire diameter
0 answers
0 votes
GATE2016-1-9
A cantilever beam having square cross-section of side $a$ is subjected to an end load. If $a$ is increased by $19\%$, the tip deflection decreases approximately by $19\%$ $29\%$ $41\%$ $50\%$
A cantilever beam having square cross-section of side $a$ is subjected to an end load. If $a$ is increased by $19\%$, the tip deflection decreases approximately by$19\%$$...
0 answers
0 votes
GATE2015-3-48
A cantilever bracket is bolted to a column using three M$12×1.75$ bolts P, Q and R. The value of maximum shear stress developed in the bolt P (in $MPa$) is ________
A cantilever bracket is bolted to a column using three M$12×1.75$ bolts P, Q and R. The value of maximum shear stress developed in the bolt P (in $MPa$) is ________
0 answers
0 votes
GATE2015-3-46
For the overhanging beam shown in figure, the magnitude of maximum bending moment (in $kN$-$m$) is ________
For the overhanging beam shown in figure, the magnitude of maximum bending moment (in $kN$-$m$) is ________
0 answers
0 votes
GATE2015-3-29
The number of degrees of freedom of the linkage shown in the figure is -$3$ $0$ $1$ $2$
The number of degrees of freedom of the linkage shown in the figure is-$3$$0$$1$$2$
0 answers
0 votes
GATE2015-3-18
A weight of $500$ $N$ is supported by two metallic ropes as shown in the figure. The values of tensions $T_1$ and $T_2$ are respectively $433$ $N$ and $250$ $N$ $250$ $N$ and $433$ $N$ $353.5$ $N$ and $250$ $N$ $250$ $N$ and $353.5$ $N$
A weight of $500$ $N$ is supported by two metallic ropes as shown in the figure. The values of tensions $T_1$ and $T_2$ are respectively$433$ $N$ and $250$ $N$$250$ $N$ a...
0 answers
0 votes
GATE2015-3-5
The strain hardening exponent $n$ of stainless steel SS $304$ with distinct yield and UTS values undergoing plastic deformation is $n < 0$ $n = 0$ $0 < n < 1$ $n = 1$
The strain hardening exponent $n$ of stainless steel SS $304$ with distinct yield and UTS values undergoing plastic deformation is$n < 0$$n = 0$$0 < n < 1$$n = 1$
0 answers
0 votes
GATE2015-3-2
For the same material and the mass, which of the following configurations of flywheel will have maximum mass moment of inertia about the axis of rotation OO’ passing through the center of gravity.
For the same material and the mass, which of the following configurations of flywheel will have maximum mass moment of inertia about the axis of rotation OO’ passing th...
0 answers
0 votes
GATE2015-3-1
For the given fluctuating fatigue load, the values of stress amplitude and stress ratio are respectively $100$ $MPa$ and $5$ $250$ $MPa$ and $5$ $100$ $MPa$ and $0.20$ $250$ $MPa$ and $0.20$
For the given fluctuating fatigue load, the values of stress amplitude and stress ratio are respectively$100$ $MPa$ and $5$$250$ $MPa$ and $5$$100$ $MPa$ and $0.20$$250$ ...
0 answers
0 votes
GATE2015-2-34
In a plane stress condition, the components of stress at a point are $\sigma_x =20$ $MPa$, $\sigma _y=80$ $MPa$ and $\tau_ {xy}$=$40$ $MPa$ The maximum shear stress (in $MPa$) at the point is $20$ $25$ $50$ $100$
In a plane stress condition, the components of stress at a point are $\sigma_x =20$ $MPa$, $\sigma _y=80$ $MPa$ and $\tau_ {xy}$=$40$ $MPa$ The maximum shear stress (in $...
0 answers
0 votes
GATE2015-2-32
For the truss shown in the figure, the magnitude of the force (in $kN$) in the member SR is $10$ $14.14$ $20$ $28.28$
For the truss shown in the figure, the magnitude of the force (in $kN$) in the member SR is$10$$14.14$$20$$28.28$
Page: