Register

GATE Mechanical 2021 Set 1 | Question: 10

• recategorized by
635 views

Please log in or register to answer this question.

Related questions

0 0 votes
0 0 answers
622
622 views
go_editor asked Mar 1, 2021
622 views
GATE Mechanical 2021 Set 2 | Question: 42
A $\text{76.2 mm}$ gauge block is used under one end of a $\text{254 mm}$ sine bar with roll diameter of $\text{25.4 mm}$. The height of gauge blocks required at the othe...
0 0 votes
0 0 answers
316
316 views
Arjun asked Feb 15, 2022
316 views
GATE Mechanical 2022 Set 1 | Question: 10
The type of fit between a mating shaft of diameter $25.0 ^{+0.010}_{- 0.010}$ $\text{mm}$ and a hole of diameter $25.015 ^{+0.015}_{- 0.015}$ $\text{mm}$ is ____________...
0 0 votes
0 0 answers
280
280 views
go_editor asked Mar 1, 2021
280 views
GATE Mechanical 2021 Set 2 | Question: 9
The allowance provided in between a hole and a shaft is calculated from the difference betweenlower limit of the shaft and the upper limit of the holeupper limit of the s...
0 0 votes
0 0 answers
401
401 views
gatecse asked Feb 22, 2021
401 views
GATE Mechanical 2021 Set 1 | Question: 1
If $y(x)$ satisfies the differential equation $(\sin x) \dfrac{\mathrm{d}y }{\mathrm{d} x} + y \cos x = 1,$subject to the condition $y(\pi/2) = \pi/2,$ then $y(\pi/6)$ is...
Voting & Accepting an answer helps improve the community

Related questions

0 0 votes
0 0 answers
622
622 views
go_editor asked Mar 1, 2021
622 views
GATE Mechanical 2021 Set 2 | Question: 42
A $\text{76.2 mm}$ gauge block is used under one end of a $\text{254 mm}$ sine bar with roll diameter of $\text{25.4 mm}$. The height of gauge blocks required at the othe...
0 0 votes
0 0 answers
316
316 views
Arjun asked Feb 15, 2022
316 views
GATE Mechanical 2022 Set 1 | Question: 10
The type of fit between a mating shaft of diameter $25.0 ^{+0.010}_{- 0.010}$ $\text{mm}$ and a hole of diameter $25.015 ^{+0.015}_{- 0.015}$ $\text{mm}$ is ____________...
0 0 votes
0 0 answers
280
280 views
go_editor asked Mar 1, 2021
280 views
GATE Mechanical 2021 Set 2 | Question: 9
The allowance provided in between a hole and a shaft is calculated from the difference betweenlower limit of the shaft and the upper limit of the holeupper limit of the s...
0 0 votes
0 0 answers
401
401 views
gatecse asked Feb 22, 2021
401 views
GATE Mechanical 2021 Set 1 | Question: 1
If $y(x)$ satisfies the differential equation $(\sin x) \dfrac{\mathrm{d}y }{\mathrm{d} x} + y \cos x = 1,$subject to the condition $y(\pi/2) = \pi/2,$ then $y(\pi/6)$ is...
← Previous · GATE Mechanical 2021...Next → · GATE Mechanical 2021...
← Previous in category · GATE2020-ME-2: 12Next in category → · GATE Mechanical 2021...
Position:
Show:
Answer:

Add Synced Question

×