Register

GATE Mechanical 2021 Set 2 | Question: 42

• recategorized by
629 views
0 0 votes
A $\text{76.2 mm}$ gauge block is used under one end of a $\text{254 mm}$ sine bar with roll diameter of $\text{25.4 mm}$. The height of gauge blocks required at the other end of the sine bar to measure an angle of $30^{\circ}$ is ______ $\text{mm} (\textit{round off to two decimal places}$).

Please log in or register to answer this question.

Related questions

0 0 votes
0 0 answers
285
285 views
go_editor asked Mar 1, 2021
285 views
GATE Mechanical 2021 Set 2 | Question: 9
The allowance provided in between a hole and a shaft is calculated from the difference betweenlower limit of the shaft and the upper limit of the holeupper limit of the s...
0 0 votes
0 0 answers
641
641 views
gatecse asked Feb 22, 2021
641 views
GATE Mechanical 2021 Set 1 | Question: 10
Consider the surface roughness profile as shown in the figureThe center line average roughness ($R_{a}$, in $\mu m$) of the measured length $\text{(L)}$ is$0$$1$$2$$4$
0 0 votes
0 0 answers
294
294 views
go_editor asked Mar 1, 2021
294 views
GATE Mechanical 2021 Set 2 | Question: 10
In forced convective heat transfer, Stanton number $\text{(St)}$, Nusselt number $\text{(Nu)}$, Reynolds number $\text{(Re)}$ and Prandtl number $\text{(Pr)}$ are related...
0 0 votes
0 0 answers
417
417 views
go_editor asked Mar 1, 2021
417 views
GATE Mechanical 2021 Set 2 | Question: 14
A plane truss $\text{PQRS}$ ($\text{PQ=RS}$, and $\angle PQR=90^{\circ}$) is shown in the figure.The forces in the members $\text{PR}$ and $\text{RS}$, respectively, are ...
Voting & Accepting an answer helps improve the community

Related questions

0 0 votes
0 0 answers
285
285 views
go_editor asked Mar 1, 2021
285 views
GATE Mechanical 2021 Set 2 | Question: 9
The allowance provided in between a hole and a shaft is calculated from the difference betweenlower limit of the shaft and the upper limit of the holeupper limit of the s...
0 0 votes
0 0 answers
641
641 views
gatecse asked Feb 22, 2021
641 views
GATE Mechanical 2021 Set 1 | Question: 10
Consider the surface roughness profile as shown in the figureThe center line average roughness ($R_{a}$, in $\mu m$) of the measured length $\text{(L)}$ is$0$$1$$2$$4$
0 0 votes
0 0 answers
294
294 views
go_editor asked Mar 1, 2021
294 views
GATE Mechanical 2021 Set 2 | Question: 10
In forced convective heat transfer, Stanton number $\text{(St)}$, Nusselt number $\text{(Nu)}$, Reynolds number $\text{(Re)}$ and Prandtl number $\text{(Pr)}$ are related...
0 0 votes
0 0 answers
417
417 views
go_editor asked Mar 1, 2021
417 views
GATE Mechanical 2021 Set 2 | Question: 14
A plane truss $\text{PQRS}$ ($\text{PQ=RS}$, and $\angle PQR=90^{\circ}$) is shown in the figure.The forces in the members $\text{PR}$ and $\text{RS}$, respectively, are ...
← Previous · GATE Mechanical 2021...Next → · GATE Mechanical 2021...
← Previous in category · GATE Mechanical 2021...Next in category → · GATE Mechanical 2021...
Position:
Show:
Answer:

Add Synced Question

×