Questions without a selected answer in Machining and Machine Tool Operations

A work piece is to be firmly held in a fixture. It is to be machined by using a plain slab milling cutter as shown in the figure below.Which one of the following options ...

During orthogonal turning by using a single point cutting tool, feed rate is $0.24 \mathrm{~mm} / \mathrm{rev}$. The uncut chip thickness is $0.23$ mm. The shear angle, t...

A drill bit during its lifetime can produce $150$ through holes in a plate at a drill-speed of $200$ RPM. If the drill-speed increases to $300$ RPM , then it can produce ...

​​​​​A plate of $30 \: mm$ thickness is fed through a rolling mill with two powered rolls. Each roll has a diameter of $500 \: mm$. The plate thickness is to be reduced t...

Cylindrical workpieces of diameter $60 \: mm$ and length $400 \:mm$ are machined on a lathe at a cutting speed of $25 \mathrm{~m} \mathrm{~min}^{-1}$ and a feed of $0.2 ...

​​​​The grinding wheel used to provide the best surface finish is$\mathrm{A} 36 \mathrm{~L} 5 \mathrm{~V}$$\mathrm{A} 54 \mathrm{~L} 5 \mathrm{~V}$$\mathrm{A} 60 \mathrm{...

A cutting tool provides a tool life of $60$ minutes while machining with the cutting speed of $60 \mathrm{~m} / \mathrm{min}$. When the same tool is used for machining th...

A blanking operation is performed on $\text{C}20$ steel sheet to obtain a circular disc having a diameter of $20 \mathrm{~mm}$ and a thickness of $2 \mathrm{~mm}$. An all...

A flat surface of a $\text{C}60$ steel having dimensions of $100 \mathrm{~mm}$ (length) $\times 200 \mathrm{~mm}$ (width) is produced by a $\text{HSS}$ slab mill cutter. ...

A cuboidal part has to be accurately positioned first, arresting six degrees of freedom and then clamped in a fixture, to be used for machining. Locating pins in the form...

In an ideal orthogonal cutting experiment (see figure), the cutting speed $V$ is $1 \mathrm{~m} / \mathrm{s}$, the rake angle of the tool $\alpha=5^{\circ}$, and the shea...

A $\text{CNC}$ machine has one of its linear positioning axes as shown in the figure, consisting of a motor rotating a lead screw, which in turn moves a nut horizontally ...

A shaft of diameter $25_{-0.07}^{-0.04}$ $\text{mm}$ is assembled in a hole of diameter $25_{-0.00}^{+0.02}$ $\text{mm}$. Match the allowance and limit parameter in Colum...

Which of these processes involve$(s)$ melting in metallic workpieces?Electrochemical machiningElectric discharge machiningLaser beam machiningElectron beam machining

A straight-teeth horizontal slab milling cutter is shown in the figure. It has $4$ teeth and diameter $(D)$ of $200$ $\text{mm}$. The rotational speed of the cutter is $1...

ln an orthogonal machining operation, the cutting and thrust forces are equal in magnitude. The uncut chip thickness is $0.5$ $\text{mm}$ and the shear angle is $15^{\cir...

A cylindrical billet of $100$ $\text{mm}$ diameter and $100$ $\text{mm}$ length is extruded by a direct extrusion process to produce a bar of $L$-section. The cross secti...

A $\text{CNC}$ worktable is driven in a linear direction by a lead screw connected directly to a stepper motor. The pitch of the lead screw is $5$ $\text{mm}$. The steppe...

Electrochemical machining operations are performed with tungsten as the tool, and copper and aluminum as two different workpiece materials. Properties of copper and alumi...

Under orthogonal cutting condition, a turning operation is carried out on a metallic workpiece at a cutting speed of $4\; m/s$. The orthogonal rake angle of the cutting t...

A $1$ $\text{mm}$ thick cylindrical tube, $100$ $\text{mm}$ in diameter, is orthogonally turned such that the entire wall thickness of the tube is cut in a single pass. T...

A $4$ $\text{mm}$ thick aluminum sheet of width $w = 100$ $\text{mm}$ is rolled in a two-roll mill of roll diameter $200$ $\text{mm}$ each. The workpiece is lubricated wi...

The machining process that involves ablation isAbrasive Jet MachiningChemical MachiningElectrochemical MachiningLaser Beam Machining

A spot welding operation performed on two pieces of steel yielded a nugget with a diameter of $\text{5 mm}$ and a thickness of $\text{1 mm}$. The welding time was $\text{...

A surface grinding operation has been performed on a Cast Iron plate having dimensions $\text{300 mm} (\textit{length}) \times \text{10 mm} (\textit{width})\times\text{50...

In a pure orthogonal turning by a zero rake angle single point carbide cutting tool, the shear force has been computed to be $\text{400 N}$. The cutting velocity, $V_{c}=...

In a machining operation, if a cutting tool traces the workpiece such that the directrix is perpendicular to the plane of the generatrix as shown in figure, the surface g...

The correct sequence of machining operations to be performed to finish a large diameter through hole isdrilling, boring, reamingboring, drilling, reamingdrilling, reaming...

In modern $\text{CNC}$ machine tools, the backlash has been eliminated bypreloaded ballscrewsrack and pinionratchet and pinionslider crank mechanism