Register
Filter

Most viewed questions in Applied Mechanics and Design

0 answers
0 votes
GATE2017 ME-1: 16
Consider a beam with circular cross-section of diameter $d$. The ratio of the second moment of area about the neutral axis to the section modulus of the area is $\dfrac{d}{2} \\$ $\dfrac{\pi d}{2} \\$ $d \\$ $\pi d$
Consider a beam with circular cross-section of diameter $d$. The ratio of the second moment of area about the neutral axis to the section modulus of the area is$\dfrac{d}...
0 answers
0 votes
GATE Mechanical 2014 Set 1 | Question: 53
For the given assembly: $25 \: H7/g8$, match Group $A$ with Group $B$ ... $P-I, Q-IV, R-III, S-II$ $P-II, Q-III, R-IV, S-I$ $P-II, Q-IV, R-III, S-I$
For the given assembly: $25 \: H7/g8$, match Group $A$ with Group $B$$$\begin{array}{|c|l|c|l|} \hline & \textbf{Group A} & & \textbf{Group B} \\ \hline P. & \text{H} & I...
0 answers
0 votes
GATE2015-3-1
For the given fluctuating fatigue load, the values of stress amplitude and stress ratio are respectively $100$ $MPa$ and $5$ $250$ $MPa$ and $5$ $100$ $MPa$ and $0.20$ $250$ $MPa$ and $0.20$
For the given fluctuating fatigue load, the values of stress amplitude and stress ratio are respectively$100$ $MPa$ and $5$$250$ $MPa$ and $5$$100$ $MPa$ and $0.20$$250$ ...
0 answers
0 votes
GATE2015-2-23
During the development of a product, an entirely new process plan is made based on design logic, examination of geometry and tolerance information. This type of process planning is known as retrieval generative variant group technology based
During the development of a product, an entirely new process plan is made based on design logic, examination of geometry and tolerance information. This type of process p...
0 answers
0 votes
GATE2017 ME-1: 17
The following figure shows the velocity-time plot for a particle travelling along a straight line. The distance covered by the particle from $t=0$ to $t=5$s is __________ m.
The following figure shows the velocity-time plot for a particle travelling along a straight line. The distance covered by the particle from $t=0$ to $t=5$s is __________...
0 answers
0 votes
GATE2015-3-5
The strain hardening exponent $n$ of stainless steel SS $304$ with distinct yield and UTS values undergoing plastic deformation is $n < 0$ $n = 0$ $0 < n < 1$ $n = 1$
The strain hardening exponent $n$ of stainless steel SS $304$ with distinct yield and UTS values undergoing plastic deformation is$n < 0$$n = 0$$0 < n < 1$$n = 1$
0 answers
0 votes
GATE2015-2-34
In a plane stress condition, the components of stress at a point are $\sigma_x =20$ $MPa$, $\sigma _y=80$ $MPa$ and $\tau_ {xy}$=$40$ $MPa$ The maximum shear stress (in $MPa$) at the point is $20$ $25$ $50$ $100$
In a plane stress condition, the components of stress at a point are $\sigma_x =20$ $MPa$, $\sigma _y=80$ $MPa$ and $\tau_ {xy}$=$40$ $MPa$ The maximum shear stress (in $...
0 answers
0 votes
GATE2016-1-52
A $300$ $mm$ thick slab is being cold rolled using roll of $600$ $mm$ diameter. If the coefficient of friction is $0.08$, the maximum possible reduction (in $mm$) is __________
A $300$ $mm$ thick slab is being cold rolled using roll of $600$ $mm$ diameter. If the coefficient of friction is $0.08$, the maximum possible reduction (in $mm$) is ____...
0 answers
0 votes
GATE2016-2-23
The value of true strain produced in compressing a cylinder to half its original length is $0.69$ $-0.69$ $0.5$ $-0.5$
The value of true strain produced in compressing a cylinder to half its original length is$0.69$$-0.69$$0.5$$-0.5$
0 answers
0 votes
GATE2016-2-8
A thin cylindrical pressure vessel with closed-ends is subjected to internal pressure. The ratio of circumferential (hoop) stress to the longitudinal stress is $0.25$ $0.50$ $1.0$ $2.0$
A thin cylindrical pressure vessel with closed-ends is subjected to internal pressure. The ratio of circumferential (hoop) stress to the longitudinal stress is$0.25$$0.50...
0 answers
0 votes
GATE2016-3-10
The number of degrees of freedom in a planar mechanism having n links and j simple hinge joints is $3 ( n− 3) − 2j$ $3(n − 1) − 2j$ $3n − 2j$ $2j − 3n + 4$
The number of degrees of freedom in a planar mechanism having n links and j simple hinge joints is$3 ( n− 3) − 2j$$3(n − 1) − 2j$$3n − 2j$$2j − 3n + 4$
Page: