Register

GATE2019 ME-1: 36

• recategorized by
347 views
0 0 votes

A circular shaft having diameter $65.00_{-0.05}^{+0.01} \: mm$ is manufactured by turning process. A $50 \: \mu m$ thick coating of TiN is deposited on the shaft. Allowed variation in TiN film thickness is $\pm 5 \mu m$. The minimum hole diameter (in mm) to just provide clearance fit is

  1. $65.01$
  2. $65.12$
  3. $64.95$
  4. $65.10$

Please log in or register to answer this question.

Related questions

0 0 votes
0 0 answers
505
505 views
Arjun asked Feb 9, 2019
505 views
GATE2019 ME-1: 35
In orthogonal turning of a cylindrical tube of wall thickness $5 \: mm$, the axial and the tangential cutting forces were measured as $1259 \: N$ and $1601 \:N$, respecti...
0 0 votes
0 0 answers
506
506 views
Arjun asked Feb 9, 2019
506 views
GATE2019 ME-1: 52
In ASA system, the side cutting and end cutting edge angles of a sharp turning tool are $45^{\circ}$ and $10^{\circ}$, respectively. The feed during cylindrical turning i...
0 0 votes
0 0 answers
462
462 views
Arjun asked Feb 9, 2019
462 views
GATE2019 ME-1: 53
Taylor’s tool life equation is given by $VT^n=C$, where $V$ is in $m/min$ and $T$ is in $min$. In a turning operation, two tools $X$ and $Y$ are used. For tool $X$, $n=0....
0 0 votes
0 0 answers
551
551 views
Arjun asked Feb 9, 2019
551 views
GATE2019 ME-1: 13
In a casting process, a vertical channel through which molten metal flows downward from pouring basin to runner for reaching the mold cavity is calledblistersprueriserpin...
Voting & Accepting an answer helps improve the community

Related questions

0 0 votes
0 0 answers
505
505 views
Arjun asked Feb 9, 2019
505 views
GATE2019 ME-1: 35
In orthogonal turning of a cylindrical tube of wall thickness $5 \: mm$, the axial and the tangential cutting forces were measured as $1259 \: N$ and $1601 \:N$, respecti...
0 0 votes
0 0 answers
506
506 views
Arjun asked Feb 9, 2019
506 views
GATE2019 ME-1: 52
In ASA system, the side cutting and end cutting edge angles of a sharp turning tool are $45^{\circ}$ and $10^{\circ}$, respectively. The feed during cylindrical turning i...
0 0 votes
0 0 answers
462
462 views
Arjun asked Feb 9, 2019
462 views
GATE2019 ME-1: 53
Taylor’s tool life equation is given by $VT^n=C$, where $V$ is in $m/min$ and $T$ is in $min$. In a turning operation, two tools $X$ and $Y$ are used. For tool $X$, $n=0....
0 0 votes
0 0 answers
551
551 views
Arjun asked Feb 9, 2019
551 views
GATE2019 ME-1: 13
In a casting process, a vertical channel through which molten metal flows downward from pouring basin to runner for reaching the mold cavity is calledblistersprueriserpin...
← Previous · GATE2019 ME-1: 37Next → · GATE2019 ME-1: 35
← Previous in category · GATE2019 ME-1: 37Next in category → · GATE2019 ME-1: 35
Position:
Show:
Answer:

Add Synced Question

×