GATE2018-1-25

Arjun asked Feb 17, 2018 • recategorized Mar 5, 2021 by Lakshman Bhaiya

See all

Please log in or register to answer this question.

Related questions

0 answers

0 votes

Arjun asked Feb 24, 2017

GATE2016-1-25
Match the following: ... $P-III, Q-II, R-I, S-IV$ $P-IV, Q-II, R-I, S-III$ $P-IV, Q-I, R-II, S-III$

Match the following:$\begin{array}{|l|l|l|l|} \hline P. & \text{Feeler guage} & I. & \text{Radius of an object} \\ \hline Q. & \text{Fillet guage} & II. & \text{Diameter ...

Arjun

28.5k points

Arjun asked Feb 24, 2017

0 answers

0 votes

go_editor asked Feb 19, 2020

GATE2020-ME-1: 43
The following data applies to basic shaft system: tolerance for hole$ = 0.002\: mm$, tolerance for shaft$ = 0.001\: mm$, allowance $= 0.003\: mm$, basic size $= 50\: mm$. The maximum hole size is _______ $mm$ (round off to $3$ decimal places).

The following data applies to basic shaft system:tolerance for hole$ = 0.002\: mm$,tolerance for shaft$ = 0.001\: mm$,allowance $= 0.003\: mm$,basic size $= 50\: mm$.The ...

go_editor

5.0k points

go_editor asked Feb 19, 2020

0 answers

0 votes

Arjun asked Feb 24, 2017

GATE2016-1-39
An inverted U-tube manometer is used to measure the pressure difference between two pipes $A$ and $B$ ,as shown in figure.pipe $A$ is carrying oil (specific gravity$=0.8$ ) and pipe $B$ is carrying water.The densities of air and water are $1.16 kg/m^3$ ... $A$ and $B$ is ________$kPa$. Acceleration due to gravity $g =10\:m/s^2$.

An inverted U-tube manometer is used to measure the pressure difference between two pipes $A$ and $B$ ,as shown in figure.pipe $A$ is carrying oil (specific gravity$=0.8$...

Arjun

28.5k points

Arjun asked Feb 24, 2017

0 answers

0 votes

Arjun asked Feb 26, 2017

GATE2017 ME-2: 53
A cylindrical pin of $25^{+0.020}_{+0.010}$ mm diameter is electroplated. Plating thickness is $2.0^{\pm0.005}$ mm. Neglecting the gauge tolerance, the diameter (in mm, up to $3$ decimal points accuracy) of the GO ring gauge to inspect the plated pin is __________.

A cylindrical pin of $25^{+0.020}_{+0.010}$ mm diameter is electroplated. Plating thickness is $2.0^{\pm0.005}$ mm. Neglecting the gauge tolerance, the diameter (in mm, u...

Arjun

28.5k points

Arjun asked Feb 26, 2017

0 answers

0 votes

Arjun asked Feb 26, 2017

GATE2017 ME-2: 11
A machine component made of a ductile material is subjected to a variable loading with $\sigma _{\text{min}}=-50$ MPa and $\sigma _{\text{max}}=-50$ MPa. If the corrected endurance limit and the yield strength for the material are $\sigma '_{e}=100$ MPa and $\sigma _{y}=300$ MPa, respectively, the factor of safety is ________.

A machine component made of a ductile material is subjected to a variable loading with $\sigma _{\text{min}}=-50$ MPa and $\sigma _{\text{max}}=-50$ MPa. If the corrected...

Arjun

28.5k points

Arjun asked Feb 26, 2017

0 reply

Please log in or register to answer this question.

0 Answers

Related questions

0