GATE2018-2-51

Arjun asked Feb 17, 2018 • edited Jan 17, 2020 by go_editor

See all

Please log in or register to answer this question.

Related questions

0 answers

0 votes

Arjun asked Feb 17, 2018

GATE2018-2-55
A vehicle powered by a spark ignition engine follows air standard Otto cycle ($\gamma =1.4$). The engine generates $70$ kW while consuming $10.3$ kg/hr of fuel. The calorific value of the fuel is $44,000 \: kJ/kg$. The compression ratio is _________ (correct to two decimal places.

A vehicle powered by a spark ignition engine follows air standard Otto cycle ($\gamma =1.4$). The engine generates $70$ kW while consuming $10.3$ kg/hr of fuel. The calor...

Arjun

28.5k points

Arjun asked Feb 17, 2018

0 answers

0 votes

Arjun asked Feb 17, 2018

GATE2018-2-54
Steam in the condenser of a thermal power plant is to be condensed at a temperature of $30^{\circ}C$ with cooling water which enters the tubes of the condenser at $14^{\circ}C$ and exists at $22^{\circ}C$ ... coefficient is $2000 \: W/m^2 \: K$. The heat transfer (in $MW$) to the condenser is _________ (correct to two decimal places).

Steam in the condenser of a thermal power plant is to be condensed at a temperature of $30^{\circ}C$ with cooling water which enters the tubes of the condenser at $14^{\c...

Arjun

28.5k points

Arjun asked Feb 17, 2018

0 answers

0 votes

Arjun asked Feb 17, 2018

GATE2018-2-53
A welding operation is being performed with voltage $= 30 \: V$ and current =$100 \: A$. The cross-sectional area of the weld bead is $20 \: mm^2$. The work-piece and filler are titanium for which the specific energy of melting is $14 \: J/mm^3$. Assuming a thermal efficiency of the welding process $70 \%$, the welding speed (in $mm/s$) is __________ (correct to two decimal places).

A welding operation is being performed with voltage $= 30 \: V$ and current =$100 \: A$. The cross-sectional area of the weld bead is $20 \: mm^2$. The work-piece and fil...

Arjun

28.5k points

Arjun asked Feb 17, 2018

0 answers

0 votes

Arjun asked Feb 17, 2018

GATE2018-2-52
A circular hole of $25 \: mm$ diameter and depth of $20 \: mm$ is machined by EDM process. The material removal rate (in $mm^3/min$) is expressed as $ 4 \times 10^4 \: IT^{-1.23}$ where $I=300 \: A $ and the melting point of the material, $T=1600^{\circ}C$. The time ( in minutes) for machining this hole is _________ (correct to two decimal places)

A circular hole of $25 \: mm$ diameter and depth of $20 \: mm$ is machined by EDM process. The material removal rate (in $mm^3/min$) is expressed as $$ 4 \times 10^4 \: I...

Arjun

28.5k points

Arjun asked Feb 17, 2018

0 answers

0 votes

Arjun asked Feb 17, 2018

GATE2018-2-50
For sand-casting a steel rectangular plate with dimensions $80 \: mm \times 120 \: mm \times 20 \: mm$, a cylindrical riser has to be designed. The height of the riser is equal to its diameter. The total solidification time for the casting in $2$ ... a solidification time for $3$ minutes in the riser, the diameter (in mm) of the riser is ________ (correct to two decimal places)

For sand-casting a steel rectangular plate with dimensions $80 \: mm \times 120 \: mm \times 20 \: mm$, a cylindrical riser has to be designed. The height of the riser is...

Arjun

28.5k points

Arjun asked Feb 17, 2018

0 reply

Please log in or register to answer this question.

0 Answers

Related questions

0