Register

GATE2019 ME-2: 53

• recategorized by
428 views
0 0 votes
A through hole is drilled in an aluminium alloy plate of $15 \: mm$ thickness with a drill bit of diameter $10$ mm, at a feed of $0.25$ mm/rev and a spindle speed of $1200$ rpm. If the specific energy required for cutting this material is $0.7 \: N \cdot m/mm^3$, the power required for drilling is ____________$W$ (round off to two decimal places)

Please log in or register to answer this question.

Related questions

0 0 votes
0 0 answers
502
502 views
Arjun asked Feb 9, 2019
502 views
GATE2019 ME-2: 25
In an electrical discharge machining process, the breakdown voltage across inter electrode gap (IEG) is $200$ V and the capacitance of the RC circuit is $50 \mu F$. The e...
0 0 votes
0 0 answers
476
476 views
Arjun asked Feb 9, 2019
476 views
GATE2019 ME-1: 53
Taylor’s tool life equation is given by $VT^n=C$, where $V$ is in $m/min$ and $T$ is in $min$. In a turning operation, two tools $X$ and $Y$ are used. For tool $X$, $n=0....
0 0 votes
0 0 answers
484
484 views
Arjun asked Feb 9, 2019
484 views
GATE2019 ME-2: 50
The figure shows a pouring arrangement for casting of a metal block. Frictional losses are negligible. The acceleration due to gravity is $9.81 \: m/s^2$ .The time (in $s...
0 0 votes
0 0 answers
363
363 views
Arjun asked Feb 9, 2019
363 views
GATE2019 ME-2: 51
A gas tungsten arc welding operation is performed using a current of $250 \: A$ and an arc voltage of $20 \: V$ at a welding speed of $5 \: mm/s$. Assuming that the arc e...
Voting & Accepting an answer helps improve the community

Related questions

0 0 votes
0 0 answers
502
502 views
Arjun asked Feb 9, 2019
502 views
GATE2019 ME-2: 25
In an electrical discharge machining process, the breakdown voltage across inter electrode gap (IEG) is $200$ V and the capacitance of the RC circuit is $50 \mu F$. The e...
0 0 votes
0 0 answers
476
476 views
Arjun asked Feb 9, 2019
476 views
GATE2019 ME-1: 53
Taylor’s tool life equation is given by $VT^n=C$, where $V$ is in $m/min$ and $T$ is in $min$. In a turning operation, two tools $X$ and $Y$ are used. For tool $X$, $n=0....
0 0 votes
0 0 answers
484
484 views
Arjun asked Feb 9, 2019
484 views
GATE2019 ME-2: 50
The figure shows a pouring arrangement for casting of a metal block. Frictional losses are negligible. The acceleration due to gravity is $9.81 \: m/s^2$ .The time (in $s...
0 0 votes
0 0 answers
363
363 views
Arjun asked Feb 9, 2019
363 views
GATE2019 ME-2: 51
A gas tungsten arc welding operation is performed using a current of $250 \: A$ and an arc voltage of $20 \: V$ at a welding speed of $5 \: mm/s$. Assuming that the arc e...
← Previous · GATE2019 ME-2: 54Next → · GATE2019 ME-2: 52
← Previous in category · GATE2019 ME-1: 13Next in category → · GATE2019 ME-2: 52
Position:
Show:
Answer:

Add Synced Question

×