Recent activity in Casting, Forming and Joining Processes / GO Mechanical

0 answers

0 votes

GATE2018-1-36
The percentage scrap in a sheet metal blanking operation of a continuous strip of sheet metal as shown in the figure is _______ (correct to two decimal places)

The percentage scrap in a sheet metal blanking operation of a continuous strip of sheet metal as shown in the figure is _______ (correct to two decimal places)

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 5, 2021

0 answers

0 votes

GATE2015-2-49
In a two-stage wire drawing operation, the fractional reduction (ratio of change in cross-sectional area to initial cross-sectional area) in the first stage is $0.4$. The fractional reduction in the second stage is $0.3$. The overall fractional reduction is $0.24$ $0.58$ $0.60$ $1.00$

In a two-stage wire drawing operation, the fractional reduction (ratio of change in cross-sectional area to initial cross-sectional area) in the first stage is $0.4$. The...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 4, 2021

0 answers

0 votes

GATE2015-2-48
A cube and a sphere made of cast iron (each of volume $1000$ $cm^3$) were cast under identical conditions. The time taken for solidifying the cube was $4$ $s$. The solidification time (in $s$) for the sphere is __________

A cube and a sphere made of cast iron (each of volume $1000$ $cm^3$) were cast under identical conditions. The time taken for solidifying the cube was $4$ $s$. The solidi...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 4, 2021

0 answers

0 votes

GATE2018-1-49
An orthogonal cutting operation is being carried out in which uncut thickness is $0.010$ mm, cutting speed is $130$ m/min, rake angle is $15^{\circ}$ and width of cut is $6$ mm. It is observed that the chip thickness is $0.015$ mm, the cutting force is $60$ N and the thrust force is $25$ N. The ratio of friction energy to total energy is _______ (correct to two decimal places).

An orthogonal cutting operation is being carried out in which uncut thickness is $0.010$ mm, cutting speed is $130$ m/min, rake angle is $15^{\circ}$ and width of cut is ...

soujanyareddy13

100 points

soujanyareddy13 retagged Nov 16, 2020

0 answers

0 votes

GATE2018-1-35
The maximum reduction in cross-sectional area per pass $(R)$ of a cold wire drawing process is $R=1-e^{-(n+1)}$, where $n$ represents the strain hardening coefficient. For the case of a perfectly plastic material, $R$ is $0.865$ $0.826$ $0.777$ $0.632$

The maximum reduction in cross-sectional area per pass $(R)$ of a cold wire drawing process is $R=1-e^{-(n+1)}$, where $n$ represents the strain hardening coefficient. Fo...

soujanyareddy13

100 points

soujanyareddy13 retagged Nov 16, 2020

0 answers

0 votes

GATE2018-2-14
Match the following products with the suitable manufacturing process: ... $P-2, Q-1, R-3, S-4$ $P-4, Q-1, R-2, S-3$ $P-1, Q-3, R-4, S-2$

Match the following products with the suitable manufacturing process:$\begin{array}{|l|l|l|l|} \hline & \textbf{Product} && \textbf{Manufacturing Process} \\ \hline P. & ...

go_editor

5.0k points

go_editor edited Sep 9, 2020

0 answers

0 votes

GATE ME 2013 | Question: 16
A cube shaped casting solidifies in $5$ $min$. The solidification time in min for a cube of the same material, which is $8$ times heavier than the original casting, will be $10$ $20$ $24$ $40$

A cube shaped casting solidifies in $5$ $min$. The solidification time in min for a cube of the same material, which is $8$ times heavier than the original casting, will ...

soujanyareddy13

100 points

soujanyareddy13 retagged May 1, 2020

0 answers

0 votes

GATE2018-2-53
A welding operation is being performed with voltage $= 30 \: V$ and current =$100 \: A$. The cross-sectional area of the weld bead is $20 \: mm^2$. The work-piece and filler are titanium for which the specific energy of melting is $14 \: J/mm^3$. Assuming a thermal efficiency of the welding process $70 \%$, the welding speed (in $mm/s$) is __________ (correct to two decimal places).

A welding operation is being performed with voltage $= 30 \: V$ and current =$100 \: A$. The cross-sectional area of the weld bead is $20 \: mm^2$. The work-piece and fil...

go_editor

5.0k points

go_editor edited Jan 17, 2020

0 answers

0 votes

GATE2018-2-52
A circular hole of $25 \: mm$ diameter and depth of $20 \: mm$ is machined by EDM process. The material removal rate (in $mm^3/min$) is expressed as $ 4 \times 10^4 \: IT^{-1.23}$ where $I=300 \: A $ and the melting point of the material, $T=1600^{\circ}C$. The time ( in minutes) for machining this hole is _________ (correct to two decimal places)

A circular hole of $25 \: mm$ diameter and depth of $20 \: mm$ is machined by EDM process. The material removal rate (in $mm^3/min$) is expressed as $$ 4 \times 10^4 \: I...

go_editor

5.0k points

go_editor edited Jan 17, 2020

0 answers

0 votes

GATE2018-2-50
For sand-casting a steel rectangular plate with dimensions $80 \: mm \times 120 \: mm \times 20 \: mm$, a cylindrical riser has to be designed. The height of the riser is equal to its diameter. The total solidification time for the casting in $2$ ... a solidification time for $3$ minutes in the riser, the diameter (in mm) of the riser is ________ (correct to two decimal places)

For sand-casting a steel rectangular plate with dimensions $80 \: mm \times 120 \: mm \times 20 \: mm$, a cylindrical riser has to be designed. The height of the riser is...

go_editor

5.0k points

go_editor edited Jan 17, 2020

0 answers

0 votes

GATE2018-2-49
Taylor's tool life equation is used to estimate the life of a batch of identical HSS twist drills by drilling through holes at constant feed in $20 \: mm$ thick mild steel plates. In test $1$, a drill lasted $300$ holes at $150$ rpm while in ... maximum number of holes that can be made by another drill from the above batch at $200$ rpm is_________ (correct to two decimal places).

Taylor's tool life equation is used to estimate the life of a batch of identical HSS twist drills by drilling through holes at constant feed in $20 \: mm$ thick mild stee...

go_editor

5.0k points

go_editor edited Jan 17, 2020

0 answers

0 votes

GATE2018-2-48
Following data correspond to an orthogonal turning of a $100 \: mm $ diameter rod on a lathe. Rake angle:$+15^{\circ}$; Uncut chip thickness: $0.5 mm$; nominal chip thickness after the cut: $1.25 \: mm$ The shear angle (in degrees) for this process is _________ (correct to two decimal places)

Following data correspond to an orthogonal turning of a $100 \: mm $ diameter rod on a lathe. Rake angle:$+15^{\circ}$; Uncut chip thickness: $0.5 mm$; nominal chip thick...

go_editor

5.0k points

go_editor edited Jan 17, 2020

0 answers

0 votes

GATE2018-2-47
A steel wire is drawn from an initial diameter $(d_i$) of $10 \: mm$ to a final diameter ($d_f$) of the $7.5 \: mm$. The half cone angle ($\alpha$) of the die is $5^{\circ}$ and the coefficient of friction ($\mu$) between the die and the wire ... The drawing stress (in MPa) required to carry out this operation is _____ (correct to two decimal places)

A steel wire is drawn from an initial diameter $(d_i$) of $10 \: mm$ to a final diameter ($d_f$) of the $7.5 \: mm$. The half cone angle ($\alpha$) of the die is $5^{\cir...

go_editor

5.0k points

go_editor edited Jan 17, 2020

0 answers

0 votes

GATE2018-2-17
The preferred option for holding an odd-shaped workpiece in a centre lathe is live and dead centres three jaw chuck lathe dog four jaw chuck

The preferred option for holding an odd-shaped workpiece in a centre lathe islive and dead centresthree jaw chucklathe dogfour jaw chuck

go_editor

5.0k points

go_editor edited Jan 16, 2020

0 answers

0 votes

GATE2018-2-15
Feed rate in slab milling operation is equal to rotation per minute (rpm) product of rpm and number of teeth in the cutter product of rpm, feed per tooth and number of teeth in the cutter product of rpm, feed per tooth and number of teeth in contact

Feed rate in slab milling operation is equal torotation per minute (rpm)product of rpm and number of teeth in the cutterproduct of rpm, feed per tooth and number of teeth...

go_editor

5.0k points

go_editor edited Jan 16, 2020