GATE2018-1-50

Arjun asked Feb 17, 2018 • edited Jan 15, 2020 by go_editor

See all

Please log in or register to answer this question.

Related questions

0 answers

0 votes

Arjun asked Feb 17, 2018

GATE2018-1-48
The true stress $(\sigma)$ - true strain $(\varepsilon)$ diagram of a strain hardening material is shown in figure. First, there is loading up to point A, i.e., up to stress of $500$ MPa and strain of $0.5$. Then from point A, there is ... . Given that the Young's modulus $E=200$ GPa, te natural strain at point B$(\varepsilon_B)$ is _____ (correct to three decimal places)

The true stress $(\sigma)$ - true strain $(\varepsilon)$ diagram of a strain hardening material is shown in figure. First, there is loading up to point A, i.e., up to str...

Arjun

28.5k points

Arjun asked Feb 17, 2018

0 answers

0 votes

Arjun asked Feb 17, 2018

GATE2018-1-39
A simply supported beam of width $100$ mm, height $200$ mm and length 4 m is carrying a uniformly distributed load of intensity $10 \: kN/m$. The maximum bending stress (in MPa) in the beam is _________ (correct to one decimal place)

A simply supported beam of width $100$ mm, height $200$ mm and length 4 m is carrying a uniformly distributed load of intensity $10 \: kN/m$. The maximum bending stress (...

Arjun

28.5k points

Arjun asked Feb 17, 2018

0 answers

0 votes

Arjun asked Feb 17, 2018

GATE2018-1-55
An electrochemical machining (ECM) is to be used to cut a through hole into a $12$ mm thick aluminum plate. The hole has a rectangular cross-section. $10 \: mm \times 30 \:mm$. The ECM operation will be accomplished in $2$ minutes, with efficiency of $90 \%$. Assuming ... , the current (in A) required is __________ (correct to two decimal places).

An electrochemical machining (ECM) is to be used to cut a through hole into a $12$ mm thick aluminum plate. The hole has a rectangular cross-section. $10 \: mm \times 30 ...

Arjun

28.5k points

Arjun asked Feb 17, 2018

0 answers

0 votes

Arjun asked Feb 17, 2018

GATE2018-1-54
Block $P$ of mass $2$ kg slides down the surface and has a speed $20 \: m/s$ at the lowest point, $Q$, where the local radius of curvature is $2$ m as shown in the figure. Assuming $g=10 \: m/s^2$, the normal force (in $N$) at $Q$ is ____ correct to two decimal places.

Block $P$ of mass $2$ kg slides down the surface and has a speed $20 \: m/s$ at the lowest point, $Q$, where the local radius of curvature is $2$ m as shown in the figure...

Arjun

28.5k points

Arjun asked Feb 17, 2018

0 answers

0 votes

Arjun asked Feb 17, 2018

GATE2018-1-53
The schematic of an external drum rotating clockwise engaging with a short shoe is shown in the figure. The shoe is mounted at point Y on a rigid lever XYZ hinged at point X. A force $F=100$ N is applied at the free end of the lever as shown. Given that the ... the shoe and the drum is $0.3$, the braking torque in (Nm) applied on the drum is _____ (correct to two decimal places)

The schematic of an external drum rotating clockwise engaging with a short shoe is shown in the figure. The shoe is mounted at point Y on a rigid lever XYZ hinged at poin...

Arjun

28.5k points

Arjun asked Feb 17, 2018

0 reply

Please log in or register to answer this question.

0 Answers

Related questions

0