Recent activity in Applications / GO Mechanical

0 answers

0 votes

ISRO2009-10
At the eye tip of a centrifugal impeller, blade velocity is $200 \: \text{m/s}$ while the uniform axial velocity at the inlet is $150 \: \text{m/s}$. If the sonic velocity is $300 \: \text{m/s}$, then the inlet Mach number of the flow will be $0.75$ $0.66$ $0.90$ $0.83$

At the eye tip of a centrifugal impeller, blade velocity is $200 \: \text{m/s}$ while the uniform axial velocity at the inlet is $150 \: \text{m/s}$. If the sonic velocit...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya edited Jun 26, 2022

0 answers

0 votes

ISRO2009-6
A necessary precaution in selection of pumps for parallel operations is that $\text{H-Q}$ characteristics of both should be identical Both pumps should be centrifugal type Both pumps should be identical There should not be change from positive to negative slope in H-Q curve

A necessary precaution in selection of pumps for parallel operations is that$\text{H-Q}$ characteristics of both should be identicalBoth pumps should be centrifugal typeB...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya edited Jun 26, 2022

0 answers

0 votes

ISRO2009-3
The correct sequence of the centrifugal pump components through which the fluid flows is Impeller, Suction pipe, Foot valve and strainer, Delivery pipe Foot valve and strainer, Suction pipe, Impeller, Delivery pipe Impeller, Suction pipe, Delivery pipe, Foot valve and strainer Suction pipe, Delivery pipe, Impeller, Foot valve and strainer

The correct sequence of the centrifugal pump components through which the fluid flows isImpeller, Suction pipe, Foot valve and strainer, Delivery pipeFoot valve and strai...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya edited Jun 26, 2022

1 answers

1 votes

GATE2019 ME-1: 49
A steam power cycle with regeneration as shown below on the $T-s$ diagram employs a single open feedwater heater for efficiency improvement. The fluid mix with each other in an open feedwater heater. The turbine is isentropic and the input (bleed) to the feedwater ... from the turbine as a percentage of the total mass flow rate at the inlet to the turbine at state $1$ is _______

A steam power cycle with regeneration as shown below on the $T-s$ diagram employs a single open feedwater heater for efficiency improvement. The fluid mix with each other...

GG

540 points

GG answered Apr 21, 2021

0 answers

0 votes

GATE2020-ME-1: 24
The compressor of a gas turbine plant, operating on an ideal intercooled Brayton cycle, accomplishes an overall compression ratio of $6$ in a two-stage compression process. Intercooling is used to cool the air coming out from the first stage to the ... gas are constant, the intercooling pressure for minimum compressor work is __________ $kPa$ (rounded off to $2$ decimal places).

The compressor of a gas turbine plant, operating on an ideal intercooled Brayton cycle, accomplishes an overall compression ratio of $6$ in a two-stage compression proces...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 6, 2021

0 answers

0 votes

GATE2020-ME-1: 54
For a Kaplan (axial flow) turbine, the outlet blade velocity diagram at a section is shown in the figure. The diameter at this section is $3\:m$.The hub and tip diameters of the blade are $2\:m$ and $4\:m$, respectively. The water volume flow ... rotational speed of the turbine is $300\:rpm$. The blade outlet angle $\beta$ is ________ degrees (round off to one decimal place).

For a Kaplan (axial flow) turbine, the outlet blade velocity diagram at a section is shown in the figure. The diameter at this section is $3\:m$.The hub and tip diam...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 6, 2021

0 answers

0 votes

GATE2019 ME-2: 33
The figure shows a heat engine (HE) working between two reservoirs. The amount of heat $(Q_2)$ rejected by the heat engine is drawn by a heat pump (HP). The heat pump receives the entire work output $(W)$ of the heat engine. If temperatures, $T_1 >T_3>T_2$, then the relation between ... $\text{COP}= 1 + \eta$ $\text{COP}= \eta^{-1}$ $\text{COP}= \eta^{-1} -1 $

The figure shows a heat engine (HE) working between two reservoirs. The amount of heat $(Q_2)$ rejected by the heat engine is drawn by a heat pump (HP). The heat pump rec...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 5, 2021

0 answers

0 votes

GATE2019 ME-2: 49
An air standard Otto cycle has thermal efficiency of $0.5$ and the mean effective pressure of the cycle is $1000 \: kPa$. For air, assume specific heat ratio $\gamma=1.4$ and specific gas constant $R=0.287 \: kJ/kg \cdot K$. If the pressure and ... $300 \: K$, respectively, then the specific net work output of the cycle is _____ $kJ/kg $ (round off to two decimal places).

An air standard Otto cycle has thermal efficiency of $0.5$ and the mean effective pressure of the cycle is $1000 \: kPa$. For air, assume specific heat ratio $\gamma=1.4$...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 5, 2021

0 answers

0 votes

GATE2019 ME-1: 10
As per common design practice, the three types of hydraulic turbines, in descending order of flow rate, are Kaplan, Francis, Pelton Pelton, Francis, Kaplan Francis, Kaplan, Pelton Pelton, Kaplan, Francis

As per common design practice, the three types of hydraulic turbines, in descending order of flow rate, areKaplan, Francis, PeltonPelton, Francis, KaplanFrancis, Kaplan, ...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 5, 2021

0 answers

0 votes

GATE2019 ME-1: 12
Consider an ideal vapor compression refrigeration cycle. If the throttling process is replaced by an isentropic expansion process, keeping all the other processes unchanged, which one of the following statements is true for the modified cycle? Coefficient of ... performance is the same as that of the original cycle Refrigerating effect is lower than that of the original cycle

Consider an ideal vapor compression refrigeration cycle. If the throttling process is replaced by an isentropic expansion process, keeping all the other processes unchang...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 5, 2021

0 answers

0 votes

GATE2019 ME-1: 31
The rotor of a turbojet engine of an aircraft has a mass $180 \: kg$ and polar moment of inertia $10 \: kg \cdot m^2$ about the rotor axis. The rotor rotates at a constant speed of $1100 \: rad/s$ in the clockwise direction when viewed from the front of the aircraft. The ... the nose goes down $162.9 \: N \cdot m$ and the nose goes up $162.9 \: N \cdot m$ and the nose goes down

The rotor of a turbojet engine of an aircraft has a mass $180 \: kg$ and polar moment of inertia $10 \: kg \cdot m^2$ about the rotor axis. The rotor rotates at a constan...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 5, 2021

0 answers

0 votes

GATE2019 ME-1: 50
A gas turbine with air as the working fluid has an isentropic efficiency of $0.70$ when operating at a pressure ratio of $3$. Now, the pressure ratio of the turbine is increased to $5$, while maintaining the same inlet conditions. Assume air as a ... the cases, the isentropic efficiency of the turbine at the pressure ratio of $5$ is ___________ (round off to two decimal places)

A gas turbine with air as the working fluid has an isentropic efficiency of $0.70$ when operating at a pressure ratio of $3$. Now, the pressure ratio of the turbine is in...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 5, 2021

0 answers

0 votes

GATE2018-1-46
An engine working on air standard Otto cycle is supplied with air at $0.1 MPa$ and $35^{\circ} \: C$. The compression ratio is $8$. The heat supplied is $500 \: kJ/kg \: K$. The maximum temperature (in $K$) of the cycle is _______ (correct to one decimal place)

An engine working on air standard Otto cycle is supplied with air at $0.1 MPa$ and $35^{\circ} \: C$. The compression ratio is $8$. The heat supplied is $500 \: kJ/kg \: ...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 5, 2021

0 answers

0 votes

GATE2018-1-45
Steam flows through a nozzle at a mess flow rate of $m=0.1 \: kg/s$ with a heat loss of $5 \: kW$. The enthalpies at inlet and exit are $2500 \: kJ/kg$ and $2350 \: kJ/kg$, respectively. Assuming negligible velocity in inlet ($C_1 \approx 0$), the velocity ($C_2$) of steam (in $m/s$) at the nozzle exit is _____ (correct to two decimal places).

Steam flows through a nozzle at a mess flow rate of $m=0.1 \: kg/s$ with a heat loss of $5 \: kW$. The enthalpies at inlet and exit are $2500 \: kJ/kg$ and $2350 \: kJ/kg...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 5, 2021

0 answers

0 votes

GATE2018-1-24
For a Pelton wheel with a given water jet velocity, the maximum output power from the Pelton wheel is obtained when the ratio of the bucket speed to the water jet speed is _____ (correct to two decimal places)

For a Pelton wheel with a given water jet velocity, the maximum output power from the Pelton wheel is obtained when the ratio of the bucket speed to the water jet speed i...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 5, 2021

0 answers

0 votes

GATE2018-1-23
An ideal gas undergoes a process from state $1 \: (T_1 = 300\: K, \: p_1 = 100 \: kPa)$ to state $2 \: (T_2 = 600 \; K, \: p_2 = 500 \: kPa)$. The specific heats of the ideal gas are: $C_p = 1 \: kJ/kg-K$ and $C_v = 0.7 \: kJ/kg-K$. The change in specific entropy of the ideal gas from state $1$ to state $2$ (in $kJ/kg-K$) is ______ (correct to two decimal places).

An ideal gas undergoes a process from state $1 \: (T_1 = 300\: K, \: p_1 = 100 \: kPa)$ to state $2 \: (T_2 = 600 \; K, \: p_2 = 500 \: kPa)$. The specific heats of the...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 5, 2021

0 answers

0 votes

GATE2017 ME-1: 36
Air contains $79\%$ $N_{2}$ and $21\%$ $O_{2}$ on a molar basis. Methane $(CH_{4})$ is burned with $50\%$ excess air than required stoichiometrically. Assuming complete combustion of methane, the molar percentage of $N_{2}$ in the products is _______.

Air contains $79\%$ $N_{2}$ and $21\%$ $O_{2}$ on a molar basis. Methane $(CH_{4})$ is burned with $50\%$ excess air than required stoichiometrically. Assuming complete c...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 5, 2021

0 answers

0 votes

GATE2017 ME-1: 35
Moist air is treated as an ideal gas mixture of water vapour and dry air (molecular weight of air$= 28.84$ and molecular weight of water $=18$). At a location, the total pressure is $100$ kPa, the temperature is $30^{\circ}$ C and the relative humidity is ... saturation pressure of water at $30^{\circ} C$ is $4246$ Pa, the mass of water vapour per kg of dry air is _________ grams.

Moist air is treated as an ideal gas mixture of water vapour and dry air (molecular weight of air$= 28.84$ and molecular weight of water $=18$). At a location, the total ...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 5, 2021

0 answers

0 votes

GATE2017 ME-1: 34
The pressure ratio across a gas turbine (for air, specific heat at constant pressure, $c_{p}=1040 J/kg.K$ and ratio of specific heats, $\gamma=1.4$) is $10$. If the inlet temperature to the turbine is $1200$ K and the isentropic efficiency is $0.9$, the gas temperature at turbine exit is ________ $K$

The pressure ratio across a gas turbine (for air, specific heat at constant pressure, $c_{p}=1040 J/kg.K$ and ratio of specific heats, $\gamma=1.4$) is $10$. If the inlet...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 5, 2021

0 answers

0 votes

GATE2017 ME-1: 33
One kg of an ideal gas (gas constant, $R= 400 J/kg.K$; specific heat at constant volume, $c_{v}=1000 J/kg.K$) at $1$ bar, and $300$ K is contained in a sealed rigid cylinder. During an adiabatic process, $100$ kJ of work is done on the system by a stirrer. The increase in entropy of the system is _______ $J/K$.

One kg of an ideal gas (gas constant, $R= 400 J/kg.K$; specific heat at constant volume, $c_{v}=1000 J/kg.K$) at $1$ bar, and $300$ K is contained in a sealed rigid cylin...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 5, 2021

0 answers

0 votes

GATE2017 ME-2: 43
A calorically perfect gas (specific heat at constant pressure $1000 \: J/kg .K$) enters and leaves a gas turbine with the same velocity. The temperatures of the gas at turbine entry and exit are $1100 \: K $and $400 \: K$, respectively. The power produced is $4.6\: MW$ ... turbine casing. The mass flow rate of the gas (in $kg/s$) through the turbine is $6.14$ $7.00$ $7.50$ $8.00$

A calorically perfect gas (specific heat at constant pressure $1000 \: J/kg .K$) enters and leaves a gas turbine with the same velocity. The temperatures of the gas at tu...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 5, 2021

0 answers

0 votes

GATE2017 ME-2: 42
In the Rankine cycle for a steam power plant, the turbine entry and exit enthalpies are $2803 \: kJ/kg$ and $1800 \: kJ/kg$, respectively. The enthalpies of water at pump entry and exit are $121 \: kJ/kg$ and $124 \: kJ/kg$, respectively. The specific steam consumption (in $kg/kW.h$) of the cycle is _________.

In the Rankine cycle for a steam power plant, the turbine entry and exit enthalpies are $2803 \: kJ/kg$ and $1800 \: kJ/kg$, respectively. The enthalpies of water at pump...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 5, 2021

0 answers

0 votes

GATE2017 ME-2: 13
Which one of the following statements is TRUE? Both Pelton and Francis turbines are impulse turbines. Francis turbine is a reaction turbine but Kaplan turbine is an impulse turbine. Francis turbine is an axial-flow reaction turbine. Kaplan turbine is an axial-flow reaction turbine.

Which one of the following statements is TRUE?Both Pelton and Francis turbines are impulse turbines.Francis turbine is a reaction turbine but Kaplan turbine is an impulse...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 5, 2021

0 answers

0 votes

GATE2016-3-47
In the vapour compression cycle shown in the figure, the evaporating and condensing temperatures are $260 \: K$ and $310 \: K$, respectively. The compressor takes in liquid-vapour mixture (state $1$) and isentropically compresses it to a dry saturated vapour condition (state ... $1$ and $0$ (in $kJ/kg$) is ____________

In the vapour compression cycle shown in the figure, the evaporating and condensing temperatures are $260 \: K$ and $310 \: K$, respectively. The compressor takes in liqu...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 5, 2021

0 answers

0 votes

GATE2016-3-46
In a $3$-stage air compressor, the inlet pressure is $p_1$, discharge pressure is $p_4$.and the intermediate pressures are $p_2$ and $p_3 ( p_2 < p_3)$. The total pressure ratio of the compressor is $10$ and the pressure ratios of the stages are equal. If $p_1 = 100$ $kPa$, the value of the pressure $p_3$ (in $kPa$) is __________

In a $3$-stage air compressor, the inlet pressure is $p_1$, discharge pressure is $p_4$.and the intermediate pressures are $p_2$ and $p_3 ( p_2 < p_3)$. The total pressur...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 5, 2021

0 answers

0 votes

GATE2016-3-45
In a mixture of dry air and water vapor at a total pressure of $750$ $mm$ of $Hg$, the partial pressure of water vapor is $20$ $mm$ of $Hg$. The humidity ratio of the air in grams of water vapor per $kg$ of dry air ($g_w/kg_{da}$) is __________

In a mixture of dry air and water vapor at a total pressure of $750$ $mm$ of $Hg$, the partial pressure of water vapor is $20$ $mm$ of $Hg$. The humidity ratio of the air...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 5, 2021

0 answers

0 votes

GATE2016-3-19
The blade and fluid velocities for an axial turbine are as shown in the figure. The magnitude of absolute velocity at entry is $300$ $m/s$ at an angle of $65^\circ$ to the axial direction, while the magnitude of the absolute velocity at exit is ... downward direction. Given that the axial (horizontal) velocity is the same at entry and exit, the specific work (in $kJ/kg$) is__________

The blade and fluid velocities for an axial turbine are as shown in the figure.The magnitude of absolute velocity at entry is $300$ $m/s$ at an angle of $65^\circ$ to the...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 5, 2021

0 answers

0 votes

GATE2016-2-47
The partial pressure of the water vapour in a moist air sample of relative humidity $70\%$ is $1.6 \: kPa$,the total pressure being $101.35 \: kPa$ ... where $p_o=101.325 \: kPa$. The dry bulb temperature of the moist air sample (in $_{}^{\circ}\textrm{C}$) is

The partial pressure of the water vapour in a moist air sample of relative humidity $70\%$ is $1.6 \: kPa$,the total pressure being $101.35 \: kPa$.moist air may be treat...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 5, 2021

0 answers

0 votes

GATE2016-2-46
A refrigerator uses $R-134a$ as its refrigerant and operates on an ideal vapour-compression refrigeration cycle between $0.14 \: MPa$ and $0.8 \: MPa$.if the mass flow rate of refrigerant is $0.05 \: kg/s$,the rate of heat rejection to the environment is_______$kW$ ... $\text{At } P=0.8 \: MPa, \: h=93.42 \: kJ/kg, \: \text{ (saturated liquid) }$

A refrigerator uses $R-134a$ as its refrigerant and operates on an ideal vapour-compression refrigeration cycle between $0.14 \: MPa$ and $0.8 \: MPa$.if the mass flow ra...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 5, 2021

0 answers

0 votes

GATE2016-2-19
Consider a simple gas turbine (Brayton) cycle and a gas turbine cycle with perfect regeneration. In both the cycles, the pressure ratio is $6$ and the ratio of the specific heats of the working medium is $1.4$. The ratio of minimum to maximum ... $K$) in the regenerative cycle. The ratio of the thermal efficiency of the simple cycle to that of the regenerative cycle is _________

Consider a simple gas turbine (Brayton) cycle and a gas turbine cycle with perfect regeneration. In both the cycles, the pressure ratio is $6$ and the ratio of the specif...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 5, 2021

0 answers

0 votes

GATE2016-2-18
The heat removal rate from a refrigerated space and the power input to the compressor are $7.2$ $kW$ and $1.8$ $kW$, respectively. The coefficient of performance (COP) of the refrigerator is ______

The heat removal rate from a refrigerated space and the power input to the compressor are $7.2$ $kW$ and $1.8$ $kW$, respectively. The coefficient of performance (COP) of...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 5, 2021

0 answers

0 votes

GATE2016-2-14
Assuming constant temperature condition and air to be an ideal gas, the variation in atmospheric pressure with height calculated from fluid statics is linear exponential quadratic cubic

Assuming constant temperature condition and air to be an ideal gas, the variation in atmospheric pressure with height calculated from fluid statics islinearexponentialqua...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 5, 2021

0 answers

0 votes

GATE2016-1-47
In a steam power plant operating on an ideal Rankine cycle, superheated steam enters the turbine at $3 \: MPa$ and $350^ \circ C$. The condenser pressure is $75$ $kPa$. The thermal efficiency of the cycle is ________ percent. Given data: For saturated liquid, at $P=75 \:kPa$ ... $T=350^\circ C$ (superheated steam), $h=3115.3 \: kJ/kg$, $s=6.7428 \: kJ/kg-K$

In a steam power plant operating on an ideal Rankine cycle, superheated steam enters the turbine at$3 \: MPa$ and $350^ \circ C$. The condenser pressure is $75$ $kPa$. Th...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 5, 2021

0 answers

0 votes

GATE2016-1-46
An ideal gas undergoes a reversible process in which the pressure varies linearly with volume. The conditions at the start (subscript $1$) and at the end (subscript $2$) of the process with usual notation are: $p_1 = 100 \: kPa$, $V_1 = 0.2 \: m^3$ ... $R=0.275\:kJ/kg-K$. The magnitude of the work required for the process (in $kJ$) is ________

An ideal gas undergoes a reversible process in which the pressure varies linearly with volume. The conditions at the start (subscript $1$) and at the end (subscript $2$) ...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 5, 2021

0 answers

0 votes

GATE2016-1-20
The “Jominy test” is used to find Young’s modulus hardenability yield strength thermal conductivity

The “Jominy test” is used to findYoung’s modulushardenabilityyield strengththermal conductivity

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 5, 2021

0 answers

0 votes

GATE2016-1-19
The INCORRECT statement about regeneration in vapor power cycle is that it increases the irreversibility by adding the liquid with higher energy content to the steam generator heat is exchanged between the expanding fluid in the turbine and the compressed ... the principle is similar to the principle of Stirling gas cycle it is practically implemented by providing feed water heaters

The INCORRECT statement about regeneration in vapor power cycle is thatit increases the irreversibility by adding the liquid with higher energy content to the steam gener...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 5, 2021

0 answers

0 votes

GATE2016-1-18
Consider two hydraulic turbines having identical specific speed and effective head at the inlet. If the speed ratio $\displaystyle{\left(\frac{N_1}{N_2}\right)}$ of the two turbines is $2$, then the respective power ratio $\displaystyle{\left(\frac{P_1}{P_2}\right)}$ is _____________

Consider two hydraulic turbines having identical specific speed and effective head at the inlet. If the speed ratio $\displaystyle{\left(\frac{N_1}{N_2}\right)}$ of the t...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 5, 2021

0 answers

0 votes

GATE2015-3-52
Which of the following statements are TRUE, when the cavitation parameter $\sigma =0$? the local pressure is reduced to vapor pressure cavitation starts boiling of liquid starts cavitation stops (i), (ii) and (iv) only (ii) and (iii) only (i) and (iii) (i), (ii) and (iii)

Which of the following statements are TRUE, when the cavitation parameter $\sigma =0$?the local pressure is reduced to vapor pressurecavitation startsboiling of liquid st...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 4, 2021

0 answers

0 votes

GATE2015-3-47
The torque (in $N$-$m$) exerted on the crank shaft of a two stroke engine can be described as $T = 10000 + 1000 \sin(2θ) − 1200 \cos(2θ)$, where $θ$ is the crank angle as measured from inner dead center position. Assuming the resisting torque to be constant, the power (in $kW$) developed by the engine at $100$ $rpm$ is ________

The torque (in $N$-$m$) exerted on the crank shaft of a two stroke engine can be described as $T = 10000 + 1000 \sin(2θ) − 1200 \cos(2θ)$, where $θ$ is the crank ang...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 4, 2021

0 answers

0 votes

GATE2015-3-45
A bullet spins as the shot is fired from a gun. For this purpose, two helical slots as shown in the figure are cut in the barrel. Projections $A$ and $B$ on the bullet engage in each of the slots. Helical slots are such that one turn of helix is completed over a ... $m$. If velocity of bullet when it exits the barrel is $20$ $m/s$, its spinning speed in $rad/s$ is ________

A bullet spins as the shot is fired from a gun. For this purpose, two helical slots as shown in the figure are cut in the barrel. Projections $A$ and $B$ on the bullet en...

Lakshman Bhaiya

21.7k points

Lakshman Bhaiya recategorized Mar 4, 2021