GATE2015-1-46

Arjun asked in Applied Mechanics and Design Feb 24, 2017 recategorized Mar 4, 2021 by Lakshman Patel RJIT

0 votes

A horizontal plate has been joined to a vertical post using four rivets arranged as shown in the figure. The magnitude of the load on the worst loaded rivet (in $N$) is _______

gateme-2015-set1
numerical-answers
applied-mechanics-and-design
machine-design
rivited-and-welded-joints

Arjun asked in Applied Mechanics and Design Feb 24, 2017 recategorized Mar 4, 2021 by Lakshman Patel RJIT

by ♦Arjun

27.4k points

0 Comments

Please log in or register to answer this question.

0 Answers

Answer:

Related questions

0 answers

0 votes

Arjun asked in Applied Mechanics and Design Feb 19, 2017

GATE Mechanical 2014 Set 4 | Question: 55
A butt weld joint is developed on steel plates having yield and ultimate tensile strength of $500$ $MPa$ and $700$ $MPa$, respectively. The thickness of the plates is $8$ $mm$ and width is $20$ $mm$. Improper selection of ... $mm$ depth along the weld. The maximum transverse tensile load (in $kN$) carrying capacity of the developed weld joint is _______

Arjun asked in Applied Mechanics and Design Feb 19, 2017

by Arjun

27.4k points

gateme-2014-set4
numerical-answers
applied-mechanics-and-design
machine-design
rivited-and-welded-joints

0 answers

0 votes

Arjun asked in Applied Mechanics and Design Feb 19, 2017

GATE Mechanical 2014 Set 3 | Question: 55
For spot welding of two steel sheets (base metal) each of $3$ $mm$ thickness, welding current of $10000$ $A$ is applied for $0.2$ $s$. The heat dissipated to the base metal is $1000$ $J$ ... $J$ and interfacial contact resistance between sheets is $0.0002$ $Ω$, the volume (in $mm^3$) of weld nugget is _______

Arjun asked in Applied Mechanics and Design Feb 19, 2017

by Arjun

27.4k points

gateme-2014-set3
numerical-answers
applied-mechanics-and-design
machine-design
rivited-and-welded-joints

0 answers

0 votes

Arjun asked in Applied Mechanics and Design Feb 19, 2017

GATE Mechanical 2014 Set 1 | Question: 25
In solid-state welding, the contamination layers between the surfaces to be welded are removed by alcohol plastic deformation water jet sand blasting

Arjun asked in Applied Mechanics and Design Feb 19, 2017

by Arjun

27.4k points

gateme-2014-set1
applied-mechanics-and-design
machine-design
rivited-and-welded-joints

0 answers

0 votes

Arjun asked in Applied Mechanics and Design Feb 19, 2017

GATE Mechanical 2014 Set 2 | Question: 32
For the three bolt system shown in the figure, the bolt material has shear yield strength of $200$ $MPa$. For a factor of safety of $2$, the minimum metric specification required for the bolt is $M8$ $M10$ $M12$ $M16$

Arjun asked in Applied Mechanics and Design Feb 19, 2017

by Arjun

27.4k points

gateme-2014-set2
applied-mechanics-and-design
machine-design
rivited-and-welded-joints

0 answers

0 votes

piyag476 asked in Applied Mechanics and Design Feb 19, 2017

GATE ME 2013 | Question: 49
A single riveted lap joint of two similar plates as shown in the figure below has the following geometrical and material details. width of the plate w = $200$ $mm$, thickness of the plate $t$ = $5$ $mm$, number of rivets $n$ = $3$, diameter of the ... plates are to be designed to avoid tearing failure, the maximum permissible load $P$ in $kN$ is $83$ $125$ $167$ $501$

piyag476 asked in Applied Mechanics and Design Feb 19, 2017

by piyag476

1.4k points

gateme-2013
applied-mechanics-and-design
machine-design
rivited-and-welded-joints

Welcome to GO Mechanical, where you can ask questions and receive answers from other members of the community.

GATE2015-1-46

0 Comments

Please log in or register to answer this question.

0 Answers

Related questions

Recent Posts