Register

GATE Mechanical 2025 | Question: 51

• edited by
338 views
0 0 votes

Two plates of thickness $10 \: mm$ each are to be joined by a transverse fillet weld on one side and the resulting structure is loaded as shown in the figure below.

If the ultimate tensile strength of the weld material is $150 \:MPa$ and the factor of safety to be used is $3$ , the minimum length of the weld required to ensure that the weld does NOT fail is ______ $mm$ (rounded off to $2$ decimal places).

Please log in or register to answer this question.

Related questions

1 1 vote
1 1 answer
448
448 views
Shubham Sharma 2 asked Mar 6, 2025
448 views
GATE Mechanical 2025 | Question: 33
​​​​​The endurance limit of a specific grade of steel is same as its yield strength. The ultimate strength of this grade of steel is twice of its yield strength. A compon...
0 0 votes
0 0 answers
543
543 views
Shubham Sharma 2 asked Mar 6, 2025
543 views
GATE Mechanical 2025 | Question: 46
The state of stress at a point is shown in the figure given below. Under plane stress assumption, the normal strain along the thickness direction $(\varepsilon_{z z})$ is...
0 0 votes
0 0 answers
205
205 views
Shubham Sharma 2 asked Mar 6, 2025
205 views
GATE Mechanical 2025 | Question: 47
A simply supported beam of length $1 \: \text{m}$ is subjected to a uniformly distributed bending moment of $1 \: \text{N m}$ per $\text{m}$ throughout the length as show...
0 0 votes
1 1 answer
743
743 views
Shubham Sharma 2 asked Mar 6, 2025
743 views
GATE Mechanical 2025 | Question: 48
An isotropic brittle material is tested in the universal testing machine. The stress-strain diagram for the material shows a bi-linear elastic behavior as shown in the fi...
Voting & Accepting an answer helps improve the community

Related questions

1 1 vote
1 1 answer
448
448 views
Shubham Sharma 2 asked Mar 6, 2025
448 views
GATE Mechanical 2025 | Question: 33
​​​​​The endurance limit of a specific grade of steel is same as its yield strength. The ultimate strength of this grade of steel is twice of its yield strength. A compon...
0 0 votes
0 0 answers
543
543 views
Shubham Sharma 2 asked Mar 6, 2025
543 views
GATE Mechanical 2025 | Question: 46
The state of stress at a point is shown in the figure given below. Under plane stress assumption, the normal strain along the thickness direction $(\varepsilon_{z z})$ is...
0 0 votes
0 0 answers
205
205 views
Shubham Sharma 2 asked Mar 6, 2025
205 views
GATE Mechanical 2025 | Question: 47
A simply supported beam of length $1 \: \text{m}$ is subjected to a uniformly distributed bending moment of $1 \: \text{N m}$ per $\text{m}$ throughout the length as show...
0 0 votes
1 1 answer
743
743 views
Shubham Sharma 2 asked Mar 6, 2025
743 views
GATE Mechanical 2025 | Question: 48
An isotropic brittle material is tested in the universal testing machine. The stress-strain diagram for the material shows a bi-linear elastic behavior as shown in the fi...
← Previous · GATE Mechanical 2025...Next → · GATE Mechanical 2025...
← Previous in category · GATE Mechanical 2024...Next in category → · GATE Mechanical 2025...
Position:
Show:
Answer:

Add Synced Question

×