GATE Mechanical 2014 Set 2 | Question: 31

Arjun asked Feb 19, 2017 • recategorized Mar 4, 2021 by Lakshman Bhaiya

See all

Please log in or register to answer this question.

Related questions

0 answers

0 votes

Arjun asked Feb 19, 2017

GATE Mechanical 2014 Set 2 | Question: 30
The flexural rigidity $(EI)$ of a cantilever beam is assumed to be constant over the length of the beam shown in figure. If a load $P$ and bending moment $PL/2$ ... $\dfrac{PL^2}{EI} \\$ $\dfrac{3}{2}\dfrac{PL^2}{EI} \\$ $\dfrac{5}{2}\dfrac{PL^2}{EI}$

The flexural rigidity $(EI)$ of a cantilever beam is assumed to be constant over the length of the beam shown in figure. If a load $P$ and bending moment $PL/2$ are appli...

Arjun

28.5k points

Arjun asked Feb 19, 2017

0 answers

0 votes

Arjun asked Feb 9, 2019

GATE2019 ME-2: 31
A prismatic, straight, elastic, cantilever beam is subjected to a linearly distributed transverse load as shown below. If the beam length is $L$, Young’s modulus $E$, and area moment of inertia $I$, the magnitude of the maximum deflection is $\dfrac{qL^4}{15EI} \\$ $\dfrac{qL^4}{30EI} \\$ $\dfrac{qL^4}{10EI} \\$ $\dfrac{qL^4}{60EI}$

A prismatic, straight, elastic, cantilever beam is subjected to a linearly distributed transverse load as shown below. If the beam length is $L$, Young’s modulus $E$, a...

Arjun

28.5k points

Arjun asked Feb 9, 2019

0 answers

0 votes

Arjun asked Feb 24, 2017

GATE2015-2-31
A cantilever beam OP is connected to another beam PQ with a pin joint as shown in the figure. A load of $10$ $kN$ is applied at the mid-point of PQ. The magnitude of bending moment (in $kN$-$m$) at fixed end O is $2.5$ $5$ $10$ $25$

A cantilever beam OP is connected to another beam PQ with a pin joint as shown in the figure. A load of $10$ $kN$ is applied at the mid-point of PQ. The magnitude of bend...

Arjun

28.5k points

Arjun asked Feb 24, 2017

0 answers

0 votes

Arjun asked Feb 19, 2017

GATE Mechanical 2014 Set 2 | Question: 55
A rectangular hole of size $100$ $mm \times 50$ $mm$ is to be made on a $5$ $mm$ thick sheet of steel having ultimate tensile strength and shear strength of $500$ $MPa$ and $300$ $MPa$, respectively. The hole is made by punching process. Neglecting the effect of clearance, the punching force (in $kN$) is $300$ $450$ $600$ $750$

A rectangular hole of size $100$ $mm \times 50$ $mm$ is to be made on a $5$ $mm$ thick sheet of steel having ultimate tensile strength and shear strength of $500$ $MPa$ a...

Arjun

28.5k points

Arjun asked Feb 19, 2017

0 answers

0 votes

Arjun asked Feb 19, 2017

GATE Mechanical 2014 Set 2 | Question: 24
The relationship between true strain ($\epsilon _T$) and engineering strain ($\epsilon _E$) in a uniaxial tension test is given as $\epsilon _E=ln(1+\epsilon _T)$ $\epsilon _E=ln(1-\epsilon _T)$ $\epsilon _T=ln(1+\epsilon _E)$ $\epsilon _T=ln(1-\epsilon _E)$

The relationship between true strain ($\epsilon _T$) and engineering strain ($\epsilon _E$) in a uniaxial tension test is given as$\epsilon _E=ln(1+\epsilon _T)$$\epsilon...

Arjun

28.5k points

Arjun asked Feb 19, 2017

0 reply

Please log in or register to answer this question.

0 Answers

Related questions

0