GATE2019 ME-2: 20

Arjun asked in Applied Mechanics and Design Feb 9, 2019 recategorized Mar 6, 2021 by Lakshman Bhaiya

0 votes

The figure shows an idealized plane truss. If a horizontal force of $300$ N is applied at point A, then the magnitude of the force produced in member CD is ____ N

gateme-2019-set2
numerical-answers
applied-mechanics-and-design
engineering-mechanics
trusses

Arjun asked in Applied Mechanics and Design Feb 9, 2019 recategorized Mar 6, 2021 by Lakshman Bhaiya

by ♦Arjun

27.5k points

0 Comments

Please log in or register to answer this question.

0 Answers

Answer:

Related questions

0 answers

0 votes

Arjun asked in Applied Mechanics and Design Feb 9, 2019

GATE2019 ME-1: 38
A truss is composed of members AB, BC, CD, AD and BD, as shown in the figure. A vertical load of $10 \: kN$ is applied at point D. The magnitude of force (in kN) in the member BC is __________

Arjun asked in Applied Mechanics and Design Feb 9, 2019

by Arjun

27.5k points

gateme-2019-set1
numerical-answers
applied-mechanics-and-design
engineering-mechanics
trusses

0 answers

0 votes

Arjun asked in Applied Mechanics and Design Feb 19, 2017

GATE Mechanical 2014 Set 2 | Question: 7
A two member truss ABC is shown in the figure. The force (in $kN$) transmitted in member AB is _______

Arjun asked in Applied Mechanics and Design Feb 19, 2017

by Arjun

27.5k points

gateme-2014-set2
numerical-answers
applied-mechanics-and-design
engineering-mechanics
trusses

0 answers

0 votes

Arjun asked in Applied Mechanics and Design Feb 24, 2017

GATE2015-1-16
Two identical trusses support a load of $100$ $N$ as shown in the figure. The length of each truss is $1.0$ $m$; cross-sectional area is $200$ $mm^2$; Young’s modulus $E$ = $200$ $GPa$. The force in the truss $AB$ (in $N$) is _________

Arjun asked in Applied Mechanics and Design Feb 24, 2017

by Arjun

27.5k points

gateme-2015-set1
numerical-answers
applied-mechanics-and-design
engineering-mechanics
trusses

0 answers

0 votes

go_editor asked in Applied Mechanics and Design Feb 19, 2020

GATE2020-ME-1: 30
The truss shown in the figure has four members of length $\text{l}$ and flexural rigidity $\text{EI}$, and one member of length $l\sqrt{2}$ and flexural rigidity $\text{4EI}$. The truss is loaded by a pair of forces of magnitude $\text{P}$ ... $\dfrac{2\pi ^{2}EI}{l^{2}} \\$ $\dfrac{\pi ^{2}EI}{2l^{2}}$

go_editor asked in Applied Mechanics and Design Feb 19, 2020

by go_editor

5.0k points

gateme-2020-set1
applied-mechanics-and-design
engineering-mechanics
trusses

0 answers

0 votes

Arjun asked in Engineering Mechanics Feb 9, 2019

GATE2019 ME-2: 45
Three sets parallel plates $LM$, $NR$ and $PQ$ are given in Figures $1$, $2$ and $3$. The view factor $F_{IJ}$ is defined as the fraction of radiation leaving plate $I$ that is intercepted by plate $J$. Assume that the values of $F_{LM}$ and $F_{NR}$ are $0.8$ and $0.4$, respectively. The value of $F_{PQ}$ (round off to one decimal place) is ____________

Arjun asked in Engineering Mechanics Feb 9, 2019

by Arjun

27.5k points

gateme-2019-set2
numerical-answers
engineering-mechanics

Welcome to GO Mechanical, where you can ask questions and receive answers from other members of the community.

GATE2019 ME-2: 20

0 Comments

Please log in or register to answer this question.

0 Answers

Related questions

Recent Posts